According to Bob Vila's April 2023 guide, a whole-house repipe across the country costs anywhere from $1,500 to $15,000, averaging close to $7,500. With PEX the pipe is the cheap part, at roughly $0.40 to $2 per linear foot where copper is $2 to $8. Labor, wall repair and permits make up the rest. Start with the page on repiping a house, or ask for a figure on the quote page.
How much should a PEX repipe run?
That guide's whole-house spread of $1,500 to $15,000 covers every material, which is why it is so wide, and it does not break PEX out. It does list pipe cost per linear foot: PEX at $0.40 to $2, and copper at $2 to $8. With the pipe itself such a minor part of the total, a PEX job is mostly about labor, access and finish repairs.
Part of PEX's price advantage is speed of installation. It arrives in long coils, turns corners without extra pieces, needs fewer fittings, and is joined without soldering, which Wikipedia notes means no torch and no open flame. The saving comes from fewer hours on site, not only the pipe price. That said, a bigger house, three bathrooms or a two-story layout costs more than a small single-story one, whatever the pipe.
What does copper cost compared with PEX?
Bob Vila's figures put copper at $2 to $8 for each linear foot, while PEX sits between $0.40 and $2, so copper pipe is often several times pricier. Copper also takes longer to install because each joint is soldered. Both can last a long time: the guide cites 50 to 100 years for copper and 80 to 100 years for PEX.
Copper is proven over many decades. Hard water and aggressive water can pit copper from inside, which is why pinhole leaks appear in older homes. PEX does not corrode, and Wikipedia says it resists chlorine and scaling, though it must be kept out of sunlight, since exposure of about 30 days may start to embrittle it. Rancho Water's own reports put average hardness around 230 to 240 mg/L in the 2020 to 2023 reports, which scales copper heaters and fixtures, though not PEX itself. For the full comparison, see PEX versus copper in Temecula and copper versus PEX.
Is there a flow rate difference between PEX and copper?
According to Wikipedia, PEX loses less pressure than rigid pipe, because the inside is smooth and the run needs fewer fittings. In practice, flow depends on the pipe's inside diameter, and for the same nominal size PEX has a slightly smaller bore than copper. A good installer sizes the lines to the fixtures, and a manifold system can keep pressure steady across the house.
We cannot give you a trustworthy flow chart here, because published figures vary by manufacturer and fitting type. Ask the plumber what sizes they plan to use and how many fixtures each line serves. For the type question, see is PEX A or B better.
What does replacing polybutylene pipe cost?
Wikipedia reports that several million homes in North America received polybutylene between about 1978 and 1997, and building codes no longer accept it. No reliable price exists for polybutylene work alone, so lean on the overall $1,500 to $15,000 range and request a quote. Replacement is a repipe, and the plumber will check for it first.
Homes of that age range, in some older Rancho California tracts, may have it, but you should not assume so without looking. A plumber looks for pipe markings under sinks and by the water heater. The failure mechanism, per Wikipedia, is that the material is broken down by chlorine and chloramine in municipal water, often from the inside, which is why a hidden leak can come with no warning. If you find polybutylene, plan a repipe before it fails. Timing is covered in our guide on when a house needs repiping.
What does a two-bathroom house repipe cost, or a mobile home?
No sourced figure exists here for a two-bathroom house alone. Bob Vila's $2,280 to $5,120 range is for plumbing a three-bedroom, 1,500-square-foot house, which suits new work. A two-bathroom repipe usually sits at the lower and middle part of the whole-house range, but the plumber must see the house. Mobile and manufactured homes have their own access issues, so ask for a quote.
What moves the total, in order of impact:
- Access. Slab homes with lines under the floor, or two-story homes with walls to open, cost more.
- Number of fixtures. Each bathroom, kitchen and laundry adds pipe and valves.
- Wall and ceiling repair. Often priced separately, and usually done by another trade.
- Permit and inspection. A repipe is generally permitted work. For a Temecula address, the Building and Safety division of Temecula can say what applies.
- Water heater and shutoffs. Many plumbers replace stops and heater connections at the same time.
Are there ways to lower the cost of a repipe?
Yes, in a few ways. Get two or three quotes with the same scope written out. Ask whether a partial repipe, such as only the attic or the slab run that is failing, makes sense. Have walls cleared and the plumber's route accessible. Schedule the work when you can leave the house, since the water is off for much of the job.
A partial repipe is worth considering if only one section is the problem, though it may leave older pipe elsewhere. What the job involves is explained in the reasons to repipe a house and the repiping process. Other work we can send a plumber for is listed on the home page.
Common questions
How many days does a PEX repipe take?
A typical home takes a few days, and the water stays off for much of each working day. Larger homes, slab jobs and homes needing a lot of wall repair take longer. The plumber should supply a schedule and say when the water will be back on each evening.
What should I ask before hiring someone to repipe with PEX?
Find out which PEX type and fitting system will be used, whether the price includes wall repair and the permit, how the plumber protects floors and furniture and who carries out inspections. Insist on a written scope and total. Go through each quote line by line instead of judging only by the bottom figure.
Must I stay in the house for the repipe?
Be reachable, and be there when the work starts and when it finishes to go over the job and sign off. Plenty of households move out for a day or two, since the water is off. The plumber needs access to every room with plumbing, plus the attic or crawlspace.
Does PEX affect water taste?
Some people notice a faint plastic taste on a new system, which usually fades after flushing the lines for a few days. Run all taps on cold for several minutes after the job. If a taste lingers, ask the plumber.
Updated