Skip to main content
Ring (951) 383-2941

Guide ยท Temecula

No hot water is coming out

When nothing but cold water comes out, the cause is usually one of a few simple faults at the heater. Check in the right order, and stop where the work becomes a plumber's job.

Revised

Hot water plan from a heater, with branches to a kitchen tap and a shower valve.

When hot water is missing at every tap, check the heater first: a gas unit probably has its pilot or burner out, an electric one has a tripped breaker or reset button, and a tankless one often shows an error code. A single cold tap means the fault lies at that fixture. Our page on water heater service covers the plumber's next steps.

What causes no hot water at any faucet?

Cold water everywhere points to the water heater itself, nearly always a loss of heat. Common causes are a gas heater whose pilot or burner went out, an electric heater with a tripped breaker, bad element or failed thermostat, a closed shutoff valve, or a tank that is empty or leaking. A tankless unit may have shut down on an error.

Begin with what you can see. Is water leaking around the base of the heater? Then close its water supply, call a plumber, and see our page on a leaking water heater. Is the water cold at a kitchen tap and a bathroom tap alike? Then the trouble lies with the heater or its supply. Only the shower? That has a separate set of causes, covered on the shower with no hot water page.

For all the possible reasons, in the sequence a plumber would test them, go to the full list of reasons hot water goes missing.

What is the first check on a gas water heater?

Confirm the gas supply valve to the heater is open, then inspect the control. Many gas heaters show a pilot flame or an igniter light there. A pilot that is out can be relit by following the label's instructions, and it stays lit only when the thermocouple works. Smell gas at any point, and you should not try again.

When you can smell gas, get out immediately and call SoCalGas on 1-800-427-2200 once outside; dial 911 if you are in danger. Touch no switches. Fixing a gas leak is contractor work, since a California contractor license is needed when labor and materials reach $1,000, and for any job that needs a permit.

Once the pilot lights and holds, turn the thermostat dial to a warm setting and let the tank heat up. A pilot that dies again within minutes means the thermocouple or gas control is failing, or a draft or vent problem is blowing it out. Stop there and book a visit. Our page on a pilot light that stays lit but no hot water deals with a lit pilot and cold water.

What is the first check on an electric water heater?

Check the heater's breaker first, and after that the red reset button hidden under the upper panel. A tripped breaker is a quick fix, while a button that keeps tripping points to a failed element, thermostat or a short. Switch the breaker off before opening any panel. Electricity and water together are dangerous, so leave the heater alone if any part is wet or it is leaking.

Front view of an electric tank with an upper and lower element, each with its own thermostat behind a panel.

Most electric tanks carry two heating elements. A dead lower one often leaves you with only a little hot water, whereas a dead upper one can leave none. No sourced price for an element or thermostat is available to us, so ask the plumber to itemize parts and labor in the quote. On an old tank, buying new generally makes better use of money when repairs would pass half of what a new heater costs.

Tanks in hard water suffer more. Rancho California Water District's own reports put average hardness around 230 to 240 mg/L, roughly 13 to 14 grains per gallon, in the 2020 to 2023 reports. That is very hard water. Scale and sediment build up on elements and burners and shorten heater life. Heaters put in during the early 2000s, when many Redhawk and Harveston homes were built, may be past their expected life, so age can be the real answer.

What if the heater is tankless, or just one faucet runs cold?

On a tankless unit, look for an error code on the screen, confirm gas or power is on, and check that water flow is strong enough to ignite it. A scaled heat exchanger, a blocked vent or a clogged inlet filter can stop it. The manual explains each code. If the fault returns after a reset, book a visit.

When only one faucet or the shower runs cold, the heater may be fine. Probable causes include a tired cartridge or mixing valve in that fixture, supply lines swapped during recent work, a clogged aerator or a stuck shutoff. A kitchen faucet with a blocked aerator can show weak or cold flow, and the screen unscrews to rinse. Rural homes on a well with an older heater can also see sediment that clogs lines.

Freeze can matter in colder rural spots such as Aguanga. A frozen exposed pipe or a slow thaw can cut hot flow in winter. Inspect exposed lines, and never use a flame to thaw pipe. Do not open the relief valve unless you know the risks, because the water is very hot.

When does a cold-water problem need a plumber?

Call if the pilot repeatedly dies, an element or breaker trips again after one reset, gas is smelled, water escapes from the tank, the flow turns rust-colored, the tank rumbles, or the heater is beyond its expected life. Also call if you cannot distinguish a gas fault from an electric one, and for any permit work. A water heater replacement generally requires a permit.

For permit questions, the City of Temecula Building and Safety counter at 41000 Main Street can be reached on 951-694-6476, and addresses beyond city limits use Riverside County. San Diego County issues permits for Fallbrook and Rainbow. To see what a new unit costs, read water heater replacement prices. To get a plumber, request a quote, say that hot water is missing, and tell us if the heater runs on gas or on electricity.

Common questions

How quickly can a heater with cold water be fixed?

Relighting or resetting a breaker is a matter of minutes. A new thermostat, element, thermocouple or valve usually runs an hour or two, and full replacement several hours. The time varies with the unit and available parts. Ask the plumber for an estimate when they arrive, and for a price prior to starting.

Which questions suit a plumber visit for cold water?

Ask whether the quote includes the call fee, parts and labor, whether repair or replacement looks likely, and what gets checked first. Get a written price before work starts, and ask if the plumber pulls the permit should a replacement be needed. Also ask how old the heater looks and what that means for repair value.

Should I be there during the visit?

Yes, or a person you trust, as access to the heater and shutoffs is needed and you must approve any price. Heaters are often in garages or closets, so clear a route. If you cannot attend, pick a time when an adult is available to admit the plumber, and settle the cost by phone.

Can I relight the pilot myself?

On many gas heaters you can, as long as no gas is smelled and the label gives the steps. If the flame will not remain lit, quit trying. Repeated failed attempts can fill the area with gas. At that point, bring in a plumber, and phone SoCalGas at any smell of gas.

Sources used

Updated